Warranty Certificate

ATTENTION

THIS PRODUCT MUST BE REGISTERED PRIOR TO ITS FIRST USE OR STORAGE.

FAILURE TO REGISTER THIS PRODUCT CAN RESULT IN LOSS OF WARRANTY.

Need To Register your Machine?

Dealer Registration

- Step 1 of 3

Name *

First

Last

Company *

Email *

Product Information

Product Serial Number *

Product Model Number *

Products Year of Manufacturing *

Purchase Date *

Current Hour Meter Reading *

Next

Product Delivery Inspection Checklist

Fill out the PDI checklist below and submit through the portal, or print the PDI Checklist here, and email it to service@barbco.com

Inspection Date *

1. FLUID LEVEL INSPECTION

Check engine oil: CAT 10w40 (CAT & Deutz), John Deere: 10w30

• Pass
• Fail
• Corrected
• N/A

Check radiator fluids. SPECIFIC to Deutz, CAT, DEERE recommendations

• Pass
• Fail
• Corrected
• N/A

Check DEF level. Note: 1/4 tank from factory

• Pass
• Fail
• Corrected
• N/A

Check transmission fluids: Mobil Trans SHC50

• Pass
• Fail
• Corrected
• N/A

Check gearbox fluids: Spirex 85w-140

• Pass
• Fail
• Corrected
• N/A

Check winch gearbox fluid: Spirex 85w-140

• Pass
• Fail
• Corrected
• N/A

2. ELECTRICAL INSPECTION

Verify battery disconnect switch functions correctly and all connections are tight. Turn the battery disconnect to the on position, turn the key to the on position and visually inspect the engine control box for error codes

• Pass
• Fail
• Corrected
• N/A

Thumb switch for the Hydraulic Clutch works on command

• Pass
• Fail
• Corrected
• N/A

Hydraulic clutch sensor is properly functioning

• Pass
• Fail
• Corrected
• N/A

Key switch is properly functioning

• Pass
• Fail
• Corrected
• N/A

E-Stops are properly functioning .

• Pass
• Fail
• Corrected
• N/A

Visually inspect all wiring harnesses & electrical connections

• Pass
• Fail
• Corrected
• N/A

3. WIRELESS REMOTE

Power remote on. Confirm status light blinks

• Pass
• Fail
• Corrected
• N/A

With the transmission in neutral, use the engine toggle to start the engine (Make sure clutch is disengaged)

• Pass
• Fail
• Corrected
• N/A

Use the engine toggle switch to stop the engine. Confirm that the clutch disengages

• Pass
• Fail
• Corrected
• N/A

Start the engine, throttle up to maximum rpm, and back down to the idle speed

• Pass
• Fail
• Corrected
• N/A

Start the engine and push the E-Stop. Confirm the clutch disengages and the engine stops

• Pass
• Fail
• Corrected
• N/A

Test the active button. Confirm the remote paddle functions will not work unless the remote is active. Confirm the active light goes out after no use

• Pass
• Fail
• Corrected
• N/A

Test all paddle functions. Confirm their function with the placard. Make sure each one is working in the correct direction

• Pass
• Fail
• Corrected
• N/A

Push the active button, and then push the clutch paddle to the engage position. Confirm the hydraulic cylinder retracts all the way before the coil timer turns off

• Pass
• Fail
• Corrected
• N/A

4. HYDRAULIC INSPECTION

Visually inspect all hydraulic connections for leaks

• Pass
• Fail
• Corrected
• N/A

Confirm that the center cylinder (if supplied) ball valve works correctly. Test extra cylinder. Fully extend and retract

• Pass
• Fail
• Corrected
• N/A

Inspect the rack & pinion system. Look for leaks behind the pinion gears

• Pass
• Fail
• Corrected
• N/A

5. SAFETY INSPECTIONS

While the ABM is running, activate each E-Stop switch individually to verify proper functionality. The unit should disengage the clutch, shut down the engine, and illuminate the red E-Stop indicator light

• Pass
• Fail
• Corrected
• N/A

While the ABM is running, remove the tethered emergency stop to confirm proper safety response. The unit should disengage the clutch, shut down the engine, and illuminate the red E-Stop indicator light

• Pass
• Fail
• Corrected
• N/A

Using the wireless remote with your ABM, activate the E-Stop switch. Confirm the unit disengages the clutch, shuts down the engine, and illuminates the red E-Stop indicator light.

• Pass
• Fail
• Corrected
• N/A

6. MAXIMUM LIFT TILT TESTING

*TAKE EXTREME CAUTION WHEN PERFORMING THIS TEST*

* Perform these checks with the ABM running at normal operating RPM and in 5th gear. The acceptable (Passing) TILT RANGE is 8 to 14 degrees. STAY CLEAR OF ABM WHEN PERFORMING THIS TEST!

Lift from NON-OPERATORS side of the ABM, to activate the Tilt Switch. Perform test 3 times

• Pass
• Fail
• Corrected
• N/A

Lift from OPERATORS side of the ABM, to activate the Tilt Switch. Perform test 3 times

• Pass
• Fail
• Corrected
• N/A

7. SAFETY STICKER INSPECTION

Confirm that all stickers and safety decals are on the machine, in proper place and orientation

• Pass
• Fail
• Corrected
• N/A

8. MISCELLANEOUS

Inspect the drive shaft for loose hardware

• Pass
• Fail
• Corrected
• N/A

Check the spoil paddles bolts. Make sure they are as tight as possible

• Pass
• Fail
• Corrected
• N/A

Confirm that the front drive pins & track bolts are included with ABM

• Pass
• Fail
• Corrected
• N/A

Confirm the push bar aligns with the track and the adjustment bolts are tight

• Pass
• Fail
• Corrected
• N/A

Information box inventory. Confirm a copy of the operation, maintenance, and parts manual are present

• Pass
• Fail
• Corrected
• N/A

Next

Is this product going into storage? *

• Yes
• No

NOTE: FLUIDS AND BATTERIES HAVE LIMITED SHELF LIFE. REFER TO MAINTENANCE SCHEDULES IN YOUR OPERATION MANUAL.

First in Service Date

(If applicable)

I, authorized Dealer Representative, hereby pledge that this product being registered has been inspected and maintained as per the recommendations set forth in the Dealer Agreement, Appendix A, Warranty Registration. *

Clear Signature

Date *

Previous

Submit

Need To Transfer Your Machine Warranty?

Warranty Transfer

- Step 1 of 2

Authorized Barbco Dealer Representative Information

Name *

First

Last

Company Name *

Email *

Product Information

Product Serial Number *

Product Model Number *

Hour Meter Reading at Time of Transfer

Not required for equipment without hour meter reading

Next

Contractor Information

Company Name *

Contact Person *

Email *

Phone Number *

I, the undersigned, acting as an authorized Barbco Dealer Representative, hereby transfer any remaining factory warranty coverage to the contractor listed above.

Barbco Authorized Dealer Representative Signature *

Clear Signature

Date / Time *

Date

Time

Submit

ATTENTION

THIS PRODUCT MUST BE COMMISSIONED WITH A WARRANTY TRANSFER

The commissioning process covers each section of this manual including important safety information, proper operating instructions and overall maintenance and care of your Barbco horizontal boring machine.

A commissioning must be performed solely by an authorized dealer and/or servicing agent.

Machine Serial Number *

Barbco Authorized Service Technician Information

Company Name *

Contact Person *

First

Last

Email *

Contractor Information

Company Name *

Contact Person *

First

Last

Email

Phone *

Address

Address Line 1

Address Line 2

City

--- Select state ---AlabamaAlaskaArizonaArkansasCaliforniaColoradoConnecticutDelawareDistrict of ColumbiaFloridaGeorgiaHawaiiIdahoIllinoisIndianaIowaKansasKentuckyLouisianaMaineMarylandMassachusettsMichiganMinnesotaMississippiMissouriMontanaNebraskaNevadaNew HampshireNew JerseyNew MexicoNew YorkNorth CarolinaNorth DakotaOhioOklahomaOregonPennsylvaniaRhode IslandSouth CarolinaSouth DakotaTennesseeTexasUtahVermontVirginiaWashingtonWest VirginiaWisconsinWyomingState

Zip Code

The following topics are to be discussed during machine commissioning. Please note that they have been reviewed by checking each applicable box. *

• Manufacture Statement
• Safe Operation Practices
• Safety Sticker Review
• Safe Operation of Equipment
• Safety Inspection of Equipment
• Safety Component Identification
• Machine Component Descriptions
• Wireless Remote Overview
• Review of Minimum Pit Dimensions
• Machine Set Up/ Track Lineup
• Operation- Thrust Function / Pressure Controls
• Operation- Winch Function
• Operation- RTS
• Auxiliary Hydraulics

I hereby pledge that this product being commissioned has been reviewed, by checking ALL of the above boxes that apply.

Contractor/User Signature

Clear Signature

Date

I hereby pledge that this product being commissioned has been properly reviewed, by checking ALL of the above boxes that apply.

Barbco Authorized Service Technician Signature

Clear Signature

Date

Submit

Release From Technical Services

This document below is to release the mentioned technician from any further training or technical advice on said mentioned jobsite. By signing this document, the customer is satisfied with the technical and training instruction from the technician.

Customer Name *

Customer Email *

Authorized Service Technician Name *

Authorized Service Technician Email *

Location *

Job *

Signature of Company Representative *

Clear Signature

Date / Time *

Date

Time

Name of Barbco Authorized Service Technician *

First

Last

Signature of Barbco Authorized Service Technician *

Clear Signature

Date / Time *

Date

Time

Submit

General Release Pertaining to Advisory Services

In consideration of Trenchless Rental Solutions Inc. and or Barbco Inc. of East Canton, Ohio, agreeing to supply one or more of its employees to render advisory and technical advise regarding horizontal boring, horizontal boring machines, accessories, directional drills, and any other rental equipment; the undersigned hereby agrees to release, discharge and hold harmless, Trenchless Rental Solutions Inc. and or Barbco Inc. and its employees, agents and representatives from any and all claims, demands, actions and causes of actions of every type and nature which may arise out of said agents, employees and representative of Trenchless Rental Solutions Inc. and or Barbco Inc. rendering such technical and advisory services on behalf of the undersigned.

Date / Time *

Date

Time

Company *

Address *

Address Line 1

Address Line 2

City

--- Select state ---AlabamaAlaskaArizonaArkansasCaliforniaColoradoConnecticutDelawareDistrict of ColumbiaFloridaGeorgiaHawaiiIdahoIllinoisIndianaIowaKansasKentuckyLouisianaMaineMarylandMassachusettsMichiganMinnesotaMississippiMissouriMontanaNebraskaNevadaNew HampshireNew JerseyNew MexicoNew YorkNorth CarolinaNorth DakotaOhioOklahomaOregonPennsylvaniaRhode IslandSouth CarolinaSouth DakotaTennesseeTexasUtahVermontVirginiaWashingtonWest VirginiaWisconsinWyomingState

Zip Code

Officer Name *

First

Last

Officer Email *

Officer Signature *

Clear Signature

Barbco Authorized Sercvice Technician Name *

First

Last

Barbco Authorized Sercvice Technician Email *

Barbco Authorized Sercvice Technician Signature *

Clear Signature

Submit

Machine Prints

Schematics 

Machine & Component Serial Numbers PDF

Maintenance Schedule

Safety Manual